Glossary entry (derived from question below)
German term or phrase:
Zug-E module
English translation:
modulus of elasticity
Added to glossary by
Kim Metzger
Dec 30, 2002 22:49
21 yrs ago
9 viewers *
German term
Zug-E module
German to English
Tech/Engineering
Materials (Plastics, Ceramics, etc.)
Again,I apologize, but I don't have much context, except that the termp appears in a table listing properties of a plastic hydraulic fluid line/brake fluid line.
Proposed translations
(English)
4 +3 | modulus of elasticity | Kim Metzger |
5 | tensile modulus of elasticity | Dr. Fred Thomson |
Proposed translations
+3
12 mins
Selected
modulus of elasticity
Dichte / Density DIN 53479 g/cm³ 0,95 0,95 0,95
Streckspannung / Tensile
stress at yield
DIN 53455 N/mm² 20 20 20
Reißdehnung / Tensile
stress at break
DIN 53455 % 40 > 50 40
Zug-E-Modul / Modulus of
elasticity
DIN 53457 N/mm² 770 > 700 770
Schlagbiegeversuch /
Impact bending test
ISO 179/1eA KJ/m² Kein Bruch /
no break
Kein Bruch / no break Kein Bruch / no break
Oberflächenhärte / Shore D DIN 53505 1) - 53 Trägermaterial:
65
Beschichtung:
53
Trägermaterial:
65
Beschichtung:
53
1.2 Tensile strength, elongation and modulus of elasticity
1.2.1 Tensile strength, elongation and modulus of elasticity of films TTM 218
Tensile strength, elongation at break and modulus of elasticity are measured according to ISO 527-1 and ISO 527-2 standard using following parameters:
Bubble Process Tenter Process
Tensile strength and elongation Modulus of elasticity Tensile strength and elongation Modulus of elasticity
Sample width, mm 15 15 15 15
Clamp distance, mm 50 250 100 100
Pulling speed, mm/min 200 25 100 10
1.2.2 Tensile strength, elongation and modulus of elasticity of capacitor paper TTM 104
These properties are measured according to ISO 1924 standard. The paper sample conditioned at 50% R.H. +23°C is cut into strips of 15mm in width and 180mm in length.
1.3 Space factor of film TTM 216
The space factor (SF) is defined by:
SF=((tm-tw)*100%)/tw, where
Tw= film thickness measured by weight methods as in 1.1.1
Tm= film thickness measured by micrometer method as in 1.1.2
1.4 Surface roughness of film TTM 215
This property is measured according to DIN 4769 standard. The average roughness Ra is used as roughness value.
1.5 Shrinkage of film TTM 213
This property is measured according to IEC 60674 standard. The percentage change of dimensions of a film sheet in size of 100mm x 100mm is determined after keeping the sheet freely hanging in an oven.
-For polypropylene film made by bubble process 10 min at 100 ± 2 °C
-For polypropylene film made by tenter process 15 min at 100 ± 2 °C
-For polyester film 10 min at 150 ± 5 °C
1.6 Surface tension TTM 302
The surface tension of polypropylene film is measured according to ASTM D 2578-94.
Streckspannung / Tensile
stress at yield
DIN 53455 N/mm² 20 20 20
Reißdehnung / Tensile
stress at break
DIN 53455 % 40 > 50 40
Zug-E-Modul / Modulus of
elasticity
DIN 53457 N/mm² 770 > 700 770
Schlagbiegeversuch /
Impact bending test
ISO 179/1eA KJ/m² Kein Bruch /
no break
Kein Bruch / no break Kein Bruch / no break
Oberflächenhärte / Shore D DIN 53505 1) - 53 Trägermaterial:
65
Beschichtung:
53
Trägermaterial:
65
Beschichtung:
53
1.2 Tensile strength, elongation and modulus of elasticity
1.2.1 Tensile strength, elongation and modulus of elasticity of films TTM 218
Tensile strength, elongation at break and modulus of elasticity are measured according to ISO 527-1 and ISO 527-2 standard using following parameters:
Bubble Process Tenter Process
Tensile strength and elongation Modulus of elasticity Tensile strength and elongation Modulus of elasticity
Sample width, mm 15 15 15 15
Clamp distance, mm 50 250 100 100
Pulling speed, mm/min 200 25 100 10
1.2.2 Tensile strength, elongation and modulus of elasticity of capacitor paper TTM 104
These properties are measured according to ISO 1924 standard. The paper sample conditioned at 50% R.H. +23°C is cut into strips of 15mm in width and 180mm in length.
1.3 Space factor of film TTM 216
The space factor (SF) is defined by:
SF=((tm-tw)*100%)/tw, where
Tw= film thickness measured by weight methods as in 1.1.1
Tm= film thickness measured by micrometer method as in 1.1.2
1.4 Surface roughness of film TTM 215
This property is measured according to DIN 4769 standard. The average roughness Ra is used as roughness value.
1.5 Shrinkage of film TTM 213
This property is measured according to IEC 60674 standard. The percentage change of dimensions of a film sheet in size of 100mm x 100mm is determined after keeping the sheet freely hanging in an oven.
-For polypropylene film made by bubble process 10 min at 100 ± 2 °C
-For polypropylene film made by tenter process 15 min at 100 ± 2 °C
-For polyester film 10 min at 150 ± 5 °C
1.6 Surface tension TTM 302
The surface tension of polypropylene film is measured according to ASTM D 2578-94.
4 KudoZ points awarded for this answer.
Comment: "Graded automatically based on peer agreement. KudoZ."
37 mins
tensile modulus of elasticity
The modulus of elasticity describes the ratio of the increase in the stress to the increasein the strain, by 0.2 % between 0.05 % and 0.25 % , with unrestrained deformation of the cross section.
Freeman. GE WB technischer Begriffe
Freeman. GE WB technischer Begriffe
Something went wrong...